|
MODELING
GRAY V3 |
MODELING
SAND |
MODELING
TAN V3 |
MODELING
WHITE V2 |
MODELING
DLP385 GRAY |
MODELING
DLP385 TAN |
EXPERT
DLP385 GRAY |
HEAT
DLP385 GRAY |
DLP SG
CLEAR |
|
| Group | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Tensile(MPa) | 53 - 58 | 58 - 65 | 52 - 59 | 57 - 63 | 42 - 46 | 40 - 46 | 62 - 70 | 55 - 75 | 67 - 70 |
| Elongation(%) | 1 - 2 | 3 - 4 | 1 - 2 | 1 - 2 | 2 - 4 | 1 - 3 | 2 - 7 | 2 - 3 | 4 - 9 |
| Impact(J/m) | 17 - 25 | 20 - 24 | 23 - 28 | 21 - 26 | 19 - 26 | 20 - 24 | 28 - 35 | 19 - 25 | - |
| Hardness(Shore) | 85 - 87D | 90 - 93D | 88 - 90D | 86 - 90D | 85 - 87D | 85 - 87D | 92 - 94D | 85 - 87D | 88 - 90D |
| Flexure Strength(MPa) | 105 - 115 | 95 - 115 | 105 - 118 | 100 - 105 | 75 - 77 | 76 - 80 | 115 - 125 | 130 - 145 | 115 - 125 |
| Flexure Modulus(MPa) | 1900 - 2100 | 1800 - 2200 | 1950 - 2100 | 2100 - 2200 | 1400 - 1450 | 1400 - 1450 | 2050 - 2200 | 2550 - 2650 | 2000 - 2300 |
| HDT(°F/°C) | - | 153.0/67.0 | - | 148/64.5 | 140.36/60.2 | 137.84/58.8 | 156.9/69.4 | 347/175 | - |
| Viscosity(cP) | 390 - 450 | 380 - 430 | 380 - 410 | 420 - 480 | 330 - 390 | 300 - 370 | 600 - 700 | 450 - 550 | 550 - 650 |
| Layer thickness(um): | - | - | - | 50, 100, and 170 | - | - | 0.05 - 0.1 mm | - | - |
| PostCure: | - | ProCure 30°C, 30min. or ProCure2: Key guide | - | ProCure 30°C, 30min | - | - | Flash 5 -30min | - | - |
| ISO 10993-5: | - | - | - | - | - | - | - | - | Pass |
| ISO 10993-10: | - | - | - | - | - | - | - | - | Pass |
| ISO 10993-23: | - | - | - | - | - | - | - | - | Pass |
DLP Resins
3D Printing Material Groups
Material Properties Table
For DLP Printer Resins
|
MODELING
GRAY V3 |
MODELING
SAND |
MODELING
TAN V3 |
MODELING
WHITE V2 |
MODELING
DLP385 GRAY |
MODELING
DLP385 TAN |
EXPERT
DLP385 GRAY |
HEAT
DLP385 GRAY |
DLP SG
CLEAR |
|
| Group | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Tensile(MPa) | 53 - 58 | 58 - 65 | 52 - 59 | 57 - 63 | 42 - 46 | 40 - 46 | 62 - 70 | 55 - 75 | 67 - 70 |
| Elongation(%) | 1 - 2 | 3 - 4 | 1 - 2 | 1 - 2 | 2 - 4 | 1 - 3 | 2 - 7 | 2 - 3 | 4 - 9 |
| Impact(J/m) | 17 - 25 | 20 - 24 | 23 - 28 | 21 - 26 | 19 - 26 | 20 - 24 | 28 - 35 | 19 - 25 | - |
| Hardness(Shore) | 85 - 87D | 90 - 93D | 88 - 90D | 86 - 90D | 85 - 87D | 85 - 87D | 92 - 94D | 85 - 87D | 88 - 90D |
| Flexure Strength(MPa) | 105 - 115 | 95 - 115 | 105 - 118 | 100 - 105 | 75 - 77 | 76 - 80 | 115 - 125 | 130 - 145 | 115 - 125 |
| Flexure Modulus(MPa) | 1900 - 2100 | 1800 - 2200 | 1950 - 2100 | 2100 - 2200 | 1400 - 1450 | 1400 - 1450 | 2050 - 2200 | 2550 - 2650 | 2000 - 2300 |
| HDT(°F/°C) | - | 153.0/67.0 | - | 148/64.5 | 140.36/60.2 | 137.84/58.8 | 156.9/69.4 | 347/175 | - |
| Viscosity(cP) | 390 - 450 | 380 - 430 | 380 - 410 | 420 - 480 | 330 - 390 | 300 - 370 | 600 - 700 | 450 - 550 | 550 - 650 |
| Layer thickness(um): | - | - | - | 50, 100, and 170 | - | - | 0.05 - 0.1 mm | - | - |
| PostCure: | - | ProCure 30°C, 30min. or ProCure2: Key guide | - | ProCure 30°C, 30min | - | - | Flash 5 -30min | - | - |
| ISO 10993-5: | - | - | - | - | - | - | - | - | Pass |
| ISO 10993-10: | - | - | - | - | - | - | - | - | Pass |
| ISO 10993-23: | - | - | - | - | - | - | - | - | Pass |
All resins tested extensively on SprintRay printers